Silicon Intake Pipe Upgrade now available

Performance Increase: 14-20hp, 22-29ft-lb
V-Box Acceleration: 60-130mph Reduced By 1.2 Seconds

The Honda FK8 Type R intake is the result of extensive design iteration through dyno testing and flow analysis. It was developed to achieve two objectives – 1) Maintain low inlet temperatures. 2) De-restrict the turbo inlet path. The first objective was met by enclosing the filter inside a carbon airbox and using the stock seal against the hood to block out the heat soak from the engine. Since the intake sits directly behind the radiator it is crucial that the filter is not exposed which would result in a loss of power through high IAT. The second objective was met by removing the flexible tubing and optimising the inlet path with a Venturi stack connected directly to the filter. Furthermore, we added a second inlet to the airbox with a scoop pulling in air from the inner wing area. This almost doubles the total cross-sectional area from which the turbo can draw as compared with the single entry on the stock system. Our carbon airbox enclosure has been designed to maximize the use of the available volume and block all sources of heat. The resulting performance gains and aesthetics are industry-leading for the FK8 Type R.

The standard airbox draws in air from a single entry duct behind the front bumper. The size of this inlet is very small at approximately 35cm^2. The demand from the turbo results in this opening becoming a restriction. However, simply opening the filter inside the engine bay is detrimental since the filter position is directly behind the radiator and once the engine warms up - the filter will become quickly saturated with heat. Our intake system solves this issue by keeping the filter enclosed inside an airbox and adding a secondary feed that opens the inlet area by another 28cm^2. This coupled with our Venturi Filter stack for smooth flow results in an immediate gain across the entire RPM range of 14-20hp. The dyno graph below shows the comparison between the stock airbox and the Eventuri intake system on a standard car with a standard map and exhaust. Dyno runs were done back to back on the same day and with the hood closed. 

We then carried out road testing using a Vbox unit to record the acceleration from 60-130mph (also 100-200Km/h). Testing was conducted on the same stretch of road - again on the same day to keep variables minimum. Results show that with just the intake added, the acceleration times from 60-130mph and also 100-200Km/h was reduced by approximately 1.2 seconds which is a significant change at such speeds. 

Acceleration results summary:

• 60-130mph with Stock intake = 15.45 seconds
• 60-130mph with Eventuri intake = 14.27 seconds
• 100-200Km/h with Stock intake =  13.04 seconds
• 100-200Km/h with Eventuri intake =12.17 seconds

Carbon version - CURRENTLY IN STOCK

Blue Kevlar version - LAST ONE!!!

Please note that we're unable to supply Eventuri Honda products to the following locations:

Belgium | Brunei | Indonesia | Luxembourg | Malaysia | Singapore | Thailand | The Netherlands | Vietnam

DESCRIPTION

Here we have our all-new FK8 Civic Type R intercooler kit, this is a direct fit kit with no need for drilling holes or cutting.

Designed to mount in the OE location, the Dream intercooler offers a higher level of performance in both flow and cooling capacity. In a beautifully engineered and affordable package, it features a hand-built core with high flow end tanks and bespoke CNC-finished inlet & outlet flanges.

We believe that using a tube and fin design, works more efficiently than a plate and bar setup. The core is 100mm deep using a single internal tube, We use an internal turbulated tube to allow better heat dissipation from the charge air temperatures.

FUN FACT: Our intercooler has also proudly helped us throughout the Time Attack season in 2019 and also win the Championship!

All cores will come powder-coated black with the option of a painted Dream logo in several colours. 

TECH SPECS

• Direct OEM Fit
• No modification required
• No Remaps required

COMPATIBLE VEHICLES

• Honda Civic Type R | FK8 2.0T K20C1 | 2017+

FITTING DETAILS

Dream Automotive offers in-house fitting on all products at our workshop in Luton, Bedfordshire. Here are the important things you need to know:

• Fitting Time -  3 Hours
• Required Additional Items/Services - No additional items or services needed.
• Dream Automotive Recommends - Honda Civic Type R | FK8 | Tuning Packages but not required.

AVAILABILITY

In-Stock

DESCRIPTION

The tuning parts are also evolving with the appearance of spark plugs in consideration of fuel efficiency improvement and environmental performance. The use of spark plugs with an ignition position projecting 2 mm more than usual has been increasing. As you are aware, in sports vehicles such as the new Honda Civic Type R (50001-50003-M45HLZ) and Suzuki Swift Sport, this type of spark plug has also been adopted. More and more cars will use this type of spark plug in the future.

M12 Long Reach High Heat Range Tuning Sparkplug with Protruding Electrode Concept and Features: M12 Long Reach Sparkplug with protruding electrode for such vehicles as Honda Civic Type R and Suzuki Swift Sport. The lineup is equivalent NGK No. 8 and No. 9 heat values, see details. New series of plugs inherits the best from the existing M series and features Ruthenium Electrode to provide a reliable spark for vehicles with increased boost or lightly tuned vehicles. By changing the centre electrode from iridium to ruthenium, it has been possible to increase the ignition and durability more than ever. Ruthenium technology is highly abrasion-resistant to maximize durability and performance to your engine. Provides more complete fuel burn than other precious metal spark plugs, resulting in quicker throttle response, smoother idle and better cold starts. Warning: Use of this spark plugs on a vehicle not compatible with protruding electrode spark plugs may lead to serious engine damage. When replacing sparkplugs, be sure to compare the shape of a new plug with installed and select an appropriate spark plug.

COMPATIBLE VEHICLES

• Ariel Atom 4 | 2.0T K20C1 | 2019+
• Honda Civic Type R | FK2 2.0T K20C1 | 2015-2016
• Honda Civic Type R | FK8 2.0T K20C1 | 2017+

FITTING DETAILS

Dream Automotive offers in-house fitting on all products at our workshop in Luton, Bedfordshire.

AVAILABILITY

Stock item

DESCRIPTION

The FlashPro allows full user tuning and data logging for your Honda Civic Type R FK8 2.0L Turbo. It includes Windows based software called FlashProManager.

The FlashPro connects from your laptop's USB port to your vehicles diagnostic port to provide tuning with a variety of calibrations along with extensive real-time and stored data logging capabilities. It enables you to tune your engine computer for:

• Intakes
• Exhausts
• Higher Octane Fuel
• Higher Boost Levels

The Hondata FlashPro is a product that delivers all the features you need and will grow with you as you upgrade your engine. 

The FlashPro is designed, manufactured and assembled in the USA. Extensive testing before shipping and stringent quality control make the FlashPro incredibly reliable.

Options include the Hondata Flashpro with FlashProManager software only, or Hondata Flashpro with FlashProManager software and jailbreaking of the ECU. The FlashPro will not work unless the ECU is unlocked/jailbroken and requires the return of your ECU to Dream Automotive (Terms & Conditions apply). For customers outside the UK, jailbreaking is also available online from Hondata directly, or the service may also be available via your local official Hondata distributor (see video below). Live Dyno Tuning at Dream Automotive is also available (see Fitting Details below).

TECH SPECS

• Programmable ECU interface
• Connects via OBDII diagnostic port
• USB 2.0 or 3.0 connection
• Works with Laptop or Desktop
• 20 hours of onboard data logging memory
• Security password
• FlashProManager Windows software
• Check and clear diagnostic codes
• Custom laptop gauges
• Dual calibration storage - upload from one of two calibrations stored in the FlashPro
• Bluetooth connection for Mobile Connectivity
• Speed limiter removed
• Boost, ignition, fuel, cam control, torque table editing
• Launch limiter
• Individual cylinder fuel trim
• Map tracing  & lambda overlay
• Advanced graphing
• 30+ advanced data logging channels

COMPATIBLE VEHICLES

• Honda Civic Type R | FK8 2.0T K20C1 | 2017+ (Outside USA/Canada/Mexico/South America Only)

FITTING DETAILS

Dream Automotive offers in-house fitting on all products at our workshop in Luton, Bedfordshire. Here are the important things you need to know:

• Fitting Cost -
• Fitting Time -
• Required Additional Items/Services - The FlashPro will not work unless the ECU is unlocked/jailbroken and requires the return of your ECU to Dream Automotive (Terms & Conditions apply). For customers outside the UK, jailbreaking is also available online from Hondata directly, or the service may also be available via your local official Hondata distributor (see video below). Live Dyno Tuning at Dream Automotive is also available.
• Dream Automotive Recommends - Hondata FK8 Fuel System

Improper installation and/or adjustment of this product can result in major engine and/or vehicle damage.

It is the responsibility of the installer and/or user of this product to ensure that it is used in compliance with all applicable local laws and regulations. If this product was purchased in error, do not install and/or use it. The purchaser must arrange to return the product(s) for a full refund.

Dream Automotive accepts no responsibility for engine and/or vehicle damage, personal injury, or invalidation of any manufacturer warranty resulting from the installation and/or adjustment of this product.

FAQ 

Q. Will this work on more than one vehicle?
A. The FlashPro is locked to one vehicle and will only work with a jailbroken ECU. 

Q. So does that mean one Hondata FlashPro can only work with one ECU or car only.
A. One ECU and vehicle at a time. You can unlock the FlashPro by returning the ECU to stock, and then transfer to another vehicle as long as that vehicle's ECU has been jailbroken.

Q. If the ECU had been reflashed by another maker, will FlashPro still work?
A. Probably, but since we do not know what changes have been made by other parties we cannot say for sure.

Q. Which ECU's are compatible with this FlashPro?
A. 5BF-E03 Euro, 5BF-J03 Japan, 5BF-Q13 Australia, 5BF-N02 South Africa (Europe, Malaysia, Singapore, Philippines, Pakistan, South Africa, Australia, New Zealand).

AVAILABILITY

Stock Item

Steering Wheel Re-Trimming

• Re-Trim - Send us your steering wheel and we will re-trim it. We aim to return your wheel within 15 working days.
• Outright Purchase or Advance Exchange - If ordering as an Advance Exchange there is a £275.00 surcharge included in the price for the Right-Hand Drive and £175 for the Left-Hand Drive, refunded upon the return of your original steering wheel.

The customer is responsible for the return postage and we recommend the use of a tracked and insured service.

Alcantara cleaning:

In order to preserve the beauty of Alcantara, it is recommended that regular cleaning is carried out. 

Daily cleaning:

It is sufficient to dust Alcantara using a soft brush, a dry microfiber cloth, or a vacuum cleaner.

Weekly/Monthly cleaning:

After having dusted Alcantara, run a slightly moistened white cotton cloth over it 

(some Alcantara cleaners see below are recommended previous customers). 

Run it over the whole Alcantara material, making sure not to wet it excessively; 

Leave to dry (overnight). Once dried, in order to restore the material, brush it delicately with a soft bristle brush.

Avoid the use of printed absorbent cloths/papers as they can release ink onto the material.

Lead Time Varies

The FK2 Type R V2 intake is an updated version of our original FK2 system which now replaces the stock rubber inlet tube with our carbon tube and custom silicon hose. The new carbon tube also incorporates the MAF sensor and so also replaces our original metal MAF tube from the original Eventuri system. The addition of the carbon tube smooths the path from the Venturi filter housing all the way to the stock turbo inlet tube and the difference is significant in terms of the extra performance gained. The rest of the intake remains the same with our cold air scoop and Venturi filter housing providing smooth airflow and low intake temperatures. By integrating an effective cold air feed, which the stock system lacks, and coupling that with our Patented Venturi housing and carbon inlet tube, our intake delivers industry-leading results – consistently.

The Eventuri Difference

The FK2 Type R V2 Eventuri system uses our Patented Carbon Fibre Housing with our Gen 2 bespoke filter, which provides an aerodynamically efficient airflow path from the filter to the turbos. Not just another cone filter with a heat shield but a unique design that invokes the Venturi effect and maintains laminar flow conditions to reduce the drag on the turbo.

AVAILABILITY

RHD - 1-2 weeks lead time

LHD - 4-6 weeks lead time 

Please note that we're unable to supply Eventuri Honda products to the following locations:

Belgium | Brunei | Indonesia | Luxembourg | Malaysia | Singapore | Thailand | The Netherlands | Vietnam

The Dream Automotive Replacement CAT pipe for the Civic FK2 is made from lightweight T304 stainless steel for longer life and to give the owner a higher flow rate with reduced back pressure to release the engine's full capabilities. 

The de-cat pipe incorporates a tangential bend turbo outlet ensuring a perfect transition through its 3.5" bend tapered down to a 3" exhaust outlet. Hand-made to the highest UK Motorsport standards, TIG welded, using water cut machined flanges we can promise an OEM fitment.

Heat management

We can offer two types of heat management,

Zircotec ceramic coating offers 30% heat reduction, It is in effect “welded” to the substrate using our proprietary metal bond system; eliminating the need for exhaust wrap; protecting components against corrosion, and continuing to perform and look good. Zircotec coating can withstand temps of up to 900°C

Lead time: pipe lead time 6 weeks + 10 working days for coating/hardlag process.

Designed and made by suspension Experts at Eibach to our specifications, this uprated 4 spring kit will offer a performance-focused ride height lowering the car by 20mm.

The lower center of gravity will offer improved handling and responsiveness whilst also enhancing the naturally aggressive stance of your FK2.

Made from the same quality Hi-Tensile steel as used by Eibach for all their springs from aftermarket through to F1, the springs go through a number of stages after coiling – pre-stress, shot peening and then electrostatically powder coated for longevity, so you can be confident you are investing in a quality solution for your Type R.

Finished in a Royal Glossy Silver and stamped with the notable names of both Dream and Eibach this is truly a ‘dream team' production.

Lead time: In stock 

On every mile of every race track, the importance of high-performance precision braking control has been proven. Total feel and response give you the confidence you need on the road. The difference between an average driver and a great driver is those who can control speed and those who cannot. Speed is nothing without control and it's a very fine line 

Each Dream Performance brake line kit is assembled in-house from the finest quality stainless steel fittings swaged directly to hard drawn tensile stainless steel braided hose.

Dream Brake line kits eliminate that 'spongy' feeling often found with rubber hoses under extreme braking conditions - the time when performance is needed the most. By replacing the original rubber hoses with our complete system you will remove this sponginess and your braking will deliver new levels of precision.

FMVSS-106 Certified for Worldwide Use

To be road legal, brake hoses must comply with the strict criteria and requirements of FMVSS-106. Set out by the Federal Motor Vehicle Safety Standards, these criteria and requirements are used by:

• DOT (United States of America)
• NHTSA (United States of America)
• ABE KBA (Germany)
• ADR (Australia)
• LTSA (New Zealand)
• IDR (Israel)
• MOT (Europe)

Dream Automotive is registered under HEL Performance products and is fully certified and registered with all the above organizations. That means you can use them anywhere in the world with utmost confidence.

WHAT'S IN THE BOX

• Stainless Steel Braided Brake Lines (6)
• Stainless Steel Banjo Bolts 
• Copper Crush Washers 
• Instruction Leaflet
• Lifetime Warranty

Lines:6

• Smoother & Stronger Braking
• Eliminate That Spongy Pedal Feeling
• Sharper and More Responsive Braking
• More Reliable Braking System
• Race Proven Technology
• Lifetime Warranty

AVAILABILITY

Available from end of May

Steering Wheel Re-Trimming

• Re-Trim - Send us your steering wheel and we will re-trim it. We aim to return your wheel within 15 working days.

There is no Outright Purchase or Advance Exchange option available for the FK2.

The customer is responsible for return postage and we recommend the use of a tracked and insured service.

Alcantara cleaning:

In order to preserve the beauty of Alcantara it is recommended that regular cleaning is carried out. 

Daily cleaning:

It is sufficient to dust Alcantara using a soft brush, a dry microfiber cloth, or a vacuum cleaner.

Weekly/Monthly cleaning:

After having dusted Alcantara, run a slightly moistened white cotton cloth over it 

(some Alcantara cleaners see below are recommended previous customers). 

Run it over the whole Alcantara material, making sure not to wet it excessively; 

Leave to dry (overnight). Once dried, in order to restore the material, brush it delicately with a soft bristle brush.

Avoid the use of printed absorbent cloths/papers as they can release ink onto the material.

Lead Time : 2 weeks from order

DESCRIPTION

Dream Automotive front seat covers have been designed to protect the original seat upholstery from everyday wear and tear helping to maintain the resale value of your vehicle. 

Dream Automotive Front seat covers are made with Heavy-duty 6oz Nylon Fabric and are tailored to fit the FK8 Front seat, either Driver or passenger. The cover has a Dream Logo embroidered onto the seat upright.

Available in different colours.

All creases disappear once fitted and used for a week.

Sold as single items

The Rear Seat Cover is available to purchase HERE!

Advisory:

For cleaning the seat covers, we suggest using just warm water with normal soap – we would advise avoiding using specific cleaning chemicals as we are unsure how they would react with the colors. Please do not machine wash the covers, as the heat and friction from the washing machine could damage the waterproof protection on the insides of the covers.

COMPATIBLE VEHICLES

• Honda Civic Type R | FK8 2.0T K20C1 | 2017-2021

AVAILABILITY

Red Centre/Black Sides - June

Black Centre/Red sides - June

Black - June

DESCRIPTION

Genuine Mugen FK8 Wind Visors, help reducing wind noise and stops rain from entering when the window is slightly open. Plus they fit and look great!

Comes with a complete fitting kit.

Fits Honda Civic Type R FK8

TECH SPEC

Average Installation Time: 0.4h
Material: Smoked acrylic.
Included: Front and Rear (4 visors)

COMPATIBLE VEHICLES

• Honda Civic Type R | FK8 2.0T K20C1 | 2017+

AVAILABILITY

K&N's replacement air filters are designed to increase horsepower and acceleration while providing excellent filtration. These filters are washable and reusable and are custom designed to fit into your existing factory air box. Their drop-in design means adding performance is simple.

K&N's replacement air filters are covered by their famous K&N Million-Mile Limited Warranty.

• Designed to boost horsepower and rate of acceleration
• Can be cleaned and used again
• High airflow with exceptional filtration
• Works with original equipment manufacturer vehicle electronics
• Will NOT void vehicle warranty 
• K&N's Million Mile Limited Warranty®

COMPATIBLE VEHICLES

• Honda Civic Type R | FK2 2.0T K20C1 | 2015+

FITTING DETAILS

Dream Automotive offers in-house fitting on all products at our workshop in Luton, Bedfordshire.

AVAILABILITY

In Stock

Dream Automotive front seat covers have been designed to protect the original seat upholstery from everyday wear and tear helping to maintain the resale value of your vehicle. 

Dream Automotive Front seat covers are made with Heavy-duty 6oz Nylon Fabric and are tailored to fit the FK2 Front seat, either Driver or passenger. The cover has a Dream Logo embroidered onto the seat upright with a zip at the back.

Available in different colours.

All creases disappear once fitted and used for a week

Sold as individual items.

Advisory:

For cleaning the seat covers, we suggest using just warm water with normal soap – we would advise avoiding using specific cleaning chemicals as we are unsure how they would react with the colours. Please do not machine wash the covers, as the heat and friction from the washing machine could damage the waterproof protection on the insides of the covers.

COMPATIBLE VEHICLES

• Honda Civic Type R | FK2 2.0T K20C1 | 2015-16

AVAILABILITY

Full Black & Full Red - IN STOCK

Black Centre/Red Sides - June

Red Centre/Black Sides - June

Wind Deflectors for Honda Civic Type R FK2  

Sold as a pair

TECH SPECS

• Direct OEM Fit

AVAILABILITY

Stock Item.

Please allow 1-2 days for dispatch